Altitude Training
Help Center

1. Unpack carefully your generator. Make sure that there is no visible damage due to transportation. If there is any damage, please take pictures and contact Altitude Training before using the generator. 2. Remove the safety strap located under the generator. If you’re planning to travel with your generator, you can leave the strap on, as it can not be placed again once removed. 3. On the oxygen port, plug the long clear tube supplied. 4. On the other end of the tube, plug the «Y» piece. On one of the side, insert the 3L balloon. On the other side, insert one grey tube. 5. Place the green filter at the other end of the last grey tube, and insert the second grey tube on the green filter. This last tube has to be inserted into one of the small side opening of the tent. 6. Place the generator in a dry and cold room for maximum effeciency. Make sure the generator has access to enough fresh air in the room. 7. Turn on the generator with the general black switch, and then with the ON/OFF button under the screen. Check the Altitude Chart on the back of the generator to set the correct altitude. 8. Use the GEAR (black valve at the front) and the FLOW (ball in the cylinder) to set your altitude. 9. Turn off the generator when not using.

1. Unpack your tent from the box. Make sure that there is no visible damage due to transportation. If there is any damage, please take pictures and contact Altitude Training before using the tent. 2. Unfold your tent on the ground and open all zips. Take one of the white fiber glass pole and start inserting it into the dedicated sleeve at one of the corner of the tent. Make sure the pins are correctly placed at each side of the pole. 3. Now it should make a nice half circle. Repeat the same operation on the other side of the tent. 4. Place gently the 3 aluminium poles on the ceiling of the tent. 5. Place the tent on your bed frame and you can now place your mattress inside the tent. Please make sure your mattress size matches the tent before hand to avoid any unwanted damage. 6. Close all zips and insert the tube of the generator in one of the small side openings.

1. Unpack your tent from the box. Make sure that there is no visible damage due to transportation. If there is any damage, please take pictures and contact Altitude Training before using the tent. 2. Unfold your tent on the ground and open all zips. Place all aluminium poles on the ground. You should have 3 different sizes. Take out of the bag all 8 corners. 3. Take 2 of the long size aluminium poles and place them in their appropriate sleeves (zip side), at the bottom of the tent. Insert all 4 corners at the ends of the aluminium poles, with on side facing upwards. 4. Take 2 of the medium size aluminium poles and place them in their appropriate sleeves (logo side), at the bottom of the tent. Insert all poles into the 4 corners to complete the bottom frame. 5. Repeat the same operation for the upper frame, but place the corners facing downwards. 6. With the help of an other person, lift the whole upper frame and place all 4 small size aluminium poles into the vertical sleeves, and all corners. 7. Place the tent on your bed frame, and place your bed inside the tent, depending of the size and setup you would like to use) 8. Close all zips and leave a small opening for the tube to get inside the tent.

To ensure a safe and effective session, please follow these safety guidelines carefully. 1. Medical & Health Precautions • Do not use the chamber in case of a respiratory tract infection, ear infection, or any condition affecting pressure tolerance. • Always consult a medical professional before starting hyperbaric oxygen therapy, especially if you have pre-existing health conditions. 2. Location & Setup • Place the chamber on a stable, flat surface, out of direct sunlight, and away from heat sources (e.g. radiators, heaters). • Ensure the room is clean, well-ventilated, and free of dust. • After each session, ventilate the room thoroughly. • Perform regular maintenance of the device, following the manufacturer’s guidelines. 3. Prohibited Items • No mobile phones, batteries, or electronic devices allowed inside the chamber. • No food or drinks inside. • Do not bring sharp objects or wear clothing with zippers, buttons, or other abrasive elements. 4. Preparation & Entry • Wear clean, soft, comfortable clothing free of metal or hard parts. • While closing the chamber: ◦ Close the safety buckles while zipping up the chamber. ◦ Ensure the silicone flap is properly positioned between the two zippers to guarantee a correct seal. ◦ Close both zippers completely. • Before starting the session, check that all valves and air outlets are unobstructed (do not block them with pillows or objects). 5. During the Session • Clear your ears regularly during pressure build-up (e.g. swallowing or performing a gentle Valsalva maneuver). • If you feel discomfort in the ears, slowly open the manual valve to relieve pressure until the discomfort subsides. • In case of ear pain, dizziness, or other discomfort, end the session immediately by releasing pressure gradually. • Ensure the oxygen mask is properly connected to the oxygen port and fits securely. 6. Treatment Duration & Guidelines • Do not exceed 90 minutes per session, unless specifically advised by a medical professional for therapeutic reasons. • Always follow the guidance of a trained professional regarding the treatment plan, session frequency, and total exposure time.